The following are the relevant parts of my
installation for Win3.11, using the trumpet winsock 
over a multiplexed packetdriver. The second packetdriver
is used for a ka9q-slipgate, running in a DOS-Box

First of all, microsofts NDIS is loaded (net start), installing a driver
for my ne2000-clone. dis_pkt9.dos then installs a packetdriver on
vec 0x65 over NDIS. This Packetdriver is multiplexed (with pktmux) 
and two packetdrivers are installed (with pktdrv) on 0x62 and 0x63.
I use 63 for the winsocket and 62 for ka9q/nos in the dos-box.
INT 61 is reserverd and at startup of ka9q I install cslipper
on INT 60.

-----------
config.sys
-----------
stacks=9,256
DEVICEhigh=C:\WINDOWS\IFSHLP.SYS

------------
autoexec.bat
------------
lh C:\WINDOWS\SMARTDRV.EXE 1024 128
C:\WINDOWS\net start
\wintcp\winsock\pktmux 3 65 /4
\wintcp\winsock\pktdrv 63 65 /!l /lt80
\wintcp\winsock\pktdrv 62 65
\wintcp\winsock\pktdrv 61 65

----------
system.ini
(dis_pkt.dos should be in the windows-dir
----------
[network drivers]
netcard=ne2000.dos
transport=ndishlp.sys,*netbeui,dis_pkt.dos
devdir=C:\WINDOWS
LoadRMDrivers=Yes

------------
protocol.ini
------------
[network.setup]
version=0x3110
netcard=ms$ne2clone,1,MS$NE2CLONE,3
transport=ms$ndishlp,MS$NDISHLP
transport=ms$netbeui,NETBEUI
lana0=ms$ne2clone,1,ms$netbeui
lana1=ms$ne2clone,1,ms$ndishlp

[protman]
DriverName=PROTMAN$
PRIORITY=MS$NDISHLP

[MS$NE2CLONE]
DriverName=MS2000$
INTERRUPT=5
IOBASE=0x340

[NE2000]
Adapters=MS$NE2CLONE

[MS$NDISHLP]
DriverName=ndishlp$
BINDINGS=MS$NE2CLONE

[NETBEUI]
DriverName=netbeui$
SESSIONS=10
NCBS=12
BINDINGS=MS$NE2CLONE
LANABASE=0

[PKTDRV]
DriverName=PKTDRV$
BINDINGS=MS$NE2CLONE
INTVEC=0x65

---------------------------------------------------------------------
This is the startbatch for my slipgate under Win3.11, working in
a DOS-box in the background:
-----------
winslip.bat
-----------
@echo off
REM initilaizing the modem ...
comtool 3e8 2 ^b6^d1^t5^d0^t5 at&f&d2&C1X3 s0=1 s2=255^cr^t5^
REM installing the slipdriver (sl0) on 0x60
cslipper port=3e8 irq=2 vec=60 ether
REM starting the login-software
lh sliplogb.com 3e8 2 60 \tcpip\ 129.13.118.30
REM starting ka9q ....
nos192.exe autoexec.nos
REM remove the login-tool
sliplogb.com 3e8 2 60 -u
REM hangup
comtool 3e8 2 ats0=0 ^cr^t15^
REM remove the slipdriver
termin 0x60


autoexec.nos
------------
# a minimum autoexec.nos for a slipgate (nos192 or nos10b)
# Attention: All IP's must belong to the same subnet!
hostname myslipgate.ciw.uni-karlsruhe.de
ip address 129.13.118.7
domain suffix ciw.uni-karlsruhe.de.

# Slipdriver (cslipper)
attach packet 0x60 sl0 5 1500
# Ethernet-Packet-driver
attach packet 0x62 en0 5 1500

# Memory
memory ibufsize 1600
memory nibufs 30

# TCP/IP
tcp mss 1460
tcp window 3000
tcp syn on

# Routing: all packtes with addresses beginning with 
# 129.13.118 remain lokal, all other packets are routed
# to the world via gateway 129.13.118.254 (class C-Net)
route add default en0 129.13.118.254
route add 129.13.118.0/24 en0

# Slip-Routing: all slip-clients use 129.13.118.30 as IP
route add 129.13.118.30 sl0
# ARP: slip and ethernet-IP use on ethernet the same 
# linklayeraddress (the hardwareaddress of the ethernetcard)
arp publish 129.13.118.30 ether 00:40:95:05:00:19

